Adding Reverb and Delay to BandLab vocals

Demo summary
The creator walks through adding a delay plugin, adjusting the filter, and dialing back the mix to roughly 20% to enhance the vocal track.
Step-by-step
- Adjust the reverb level to tuck it into the mix
- Click Add to insert a delay plugin
- Increase the filter setting on the delay
- Turn the delay mix down to approximately 20% or below
- Test the vocal processing against the beat
Tips
- Avoid using too much reverb for this specific vocal style
- Bring the delay mix down to about 20% or lower to keep it subtle
All demos from “This Makes AUTOTUNE in BANDLAB sound REAL”
0:161:03Configuring Auto-Pitch and EQ in BandLabThe creator demonstrates the difference between 'Classic' and 'Natural' auto-tune settings in BandLab and shows how to apply EQ and compression to clean up the vocal signal flow.Bandlab· AI Audio Editor
2:330:39Adding Reverb and Delay to BandLab vocalsCurrentThe creator walks through adding a delay plugin, adjusting the filter, and dialing back the mix to roughly 20% to enhance the vocal track.Bandlab· AI Audio Editor
4:501:45Swapping Reverb types and adjusting Studio VerbThe creator demonstrates switching between Spring Verb and Studio Verb in BandLab, adjusting the size, tone, and mix to prevent the effect from overpowering the vocal.Bandlab· AI Audio Editor
6:440:41Widening vocals with Stereo effectsThe creator demonstrates how to use stereo widening tools in BandLab to thicken the vocal and adjust the frequency around 5K.Bandlab· AI Audio Editor- Watch “This Makes AUTOTUNE in BANDLAB sound REAL” →
AI Audio Editor
0:090:15Fade out songs in BandLabThe creator demonstrates how to use the slider tool in BandLab to create a professional fade-out for tracks that are too long.BkOnWhatt
3:082:12Recording and managing vocal tracks in BandLabThe user demonstrates recording multiple vocal takes, managing track limits by deleting unused tracks, and adjusting volume levels within the DAW.busic
0:280:16Setting up a project in BandLabThe creator demonstrates importing a beat into BandLab, using a song keyfinder to set the autotune, and enabling the metronome to maintain timing.BkOnWhatt
4:182:14Punching in vocals and layering in BandLabMdot 59 demonstrates the 'punch in' technique in BandLab, recording short vocal segments and immediately playing them back to ensure they sit correctly in the mix.More Mdot 59
19:141:18Refining vocal delivery and timingThe creator walks through re-recording specific lines to improve the flow and timing of the drill track within the BandLab interface.More Mdot 59
0:150:55Setting up the project and Auto-Pitch in BandLabThe creator demonstrates the initial setup in BandLab, including importing a beat, adjusting its volume, and configuring the Auto-Pitch key and scale settings.Sky Jordxn
1:100:36Applying Gain plugin to vocalsThe creator adds a gain plugin to the vocal chain in BandLab to act as a preamp, demonstrating how it increases the vocal signal level.Sky Jordxn
1:462:38Vocal EQ and frequency sculptingThe creator demonstrates how to use the EQ plugin in BandLab to roll off low-end frequencies around 107-120Hz and adjust high-end brightness while listening to the track.Sky Jordxn
4:241:21Configuring 76 and 2A CompressorsThe creator walks through setting up a serial compression chain using the 76 compressor (4:1 ratio, fast release) followed by a 2A compressor to smooth out the vocal dynamics.Sky Jordxn
2:270:21Adjusting Tape Sim saturation in BandLabThe creator demonstrates the Tape Sim effect in BandLab, slowly turning up the drive to show how it adds saturation and width to the vocals.BkOnWhatt
4:361:04Mixing vocals with BandLab Graphic EQThe creator walks through the Graphic EQ in BandLab, adjusting specific frequency bands (100Hz, 800Hz, and 6.4kHz) to demonstrate how they affect bass, presence, and sparkle.BkOnWhatt
1:510:09Set project BPM and Key in BandLabThe creator demonstrates how to access the settings icon to verify and set the song's tempo and key to ensure effects like AutoPitch function correctly.BandLab
Bandlab